Fountain Considerations

[ HOME ] - [ DESIGNS ] - [ PRODUCT CARE & INFORMATION ] - [ CONTACT - Classic Garden Ornaments, Ltd. ] - [ SEARCH ]

Download PDF Format

Classic Garden Ornaments, Ltd., designs and manufactures dry cast limestone planters and garden ornaments. We are not fountain specialists and can, at best, give only general suggestions about planters used as fountain elements. Please seek the advice of a fountain specialist for the design, installation, maintenance and winter care of any fountain. Due to local variations in climate and in building code requirements, we suggest finding a local fountain specialist. Please consult with your fountain specialist for advice regarding questions such as:

			• size of fountain • height of water fall • diameter of pool • depth of pool • splash retention • height of pool surround • piping and plumbing • nozzle selection • desired water flow • pump selection • pump location • electric wiring • installation • sealing • winter care • maintenance

SUGGESTIONS
	The water in a fountain, while soothing and beautiful in a garden or a courtyard, has certain potentially harmful properties that require attention when used in or around Longshadow dry cast limestone planters.
	Moving water can cause erosion. ~ A natural stone sealer is required to prevent erosion. Agitated water can cause natural stone sealer to break down prematurely. ~ The condition of the sealer must be monitored. Water can seep through the porous walls of Longshadow planters and cause lime-bloom. ~ Well maintained sealer is required to prevent erosion and lime-bloom. Chemicals in local water can cause staining. ~ Pool specialists or other technical experts might be able to give advice on how to remove or control staining. Falling water can create splash that goes outside its pool. ~ Pool surrounds should be high enough and wide enough. Water will expand as it freezes. ~ Winter care requires attention to the effects of freezing water.

SEALING
	We apply one coat of sealant to fountains. The installer must apply stone sealer following directions, such as those that follow. We do not seal planters and garden ornaments.
MAINTENANCE
	The fountain specialist, the designer, the installer and the owner should develop a program that includes fountain and pump maintenance, sealer maintenance and winter care.
		The maintenance program should include:
		~ a regular program to reapply sealer to prevent erosion and lime-bloom ~ monitoring the condition of the sealer by checking for the appearance of erosion on the inside and lime-bloom on the outside and underside of a fountain and ~ arranging removal of the lime-bloom and re-applying sealer.
LIME-BLOOM CAN BE REMOVED BY FOLLOWING THESE STEPS
		~ drain fountain ~ gently scrape and sand off the lime-bloom ~ rinse and repeat ~ try pressure washing, if needed ~ clean inside of bowl ~ allow to dry ~ apply natural stone sealer ~ allow sealer to dry ~ apply a second coat of natural stone sealer ~ allow sealer to dry ~ fill and turn on the fountain
	Delay will cause additional build up of lime-bloom, making it increasingly difficult to remove.
THE FOLLOWING INSTRUCTIONS ARE FROM DRYLOK:

THE FOLLOWING INSTRUCTIONS AND PRODUCT DATA ARE FROM QUIKRETE:

PRODUCT INFORMATION

PRODUCT: 02-51092 DESCRIPTION: Natural Look Waterproofer
FEATURES: This product forms a long lasting, waterproofing seal on concrete, brick, masonry, exposed aggregate, natural stone
and pavers. This sealer is fortified with new, heavy-duty resin technology to protect against the sun’s powerful rays, water,
gasoline and deicing salts. This protective sealer allows the natural look of the surface to come through. Do not use below grade.

SURFACE PREPARATION:
General: All surfaces must be clean, dry and free of all loose, peeling paint or contaminants. Bare Concrete: Allow 60 days
minimum for new concrete to cure before sealing. Previously Sealed Surfaces: Clean with an all-purpose cleaner (TSP or
substitute). Previously sealed surfaces must be porous and able to accept additional sealer. Test surface porosity before
sealing: Avoid using this product on non-porous, sealed surfaces. To test, place a few drops of water on surface. If water sinks
in, the surface is porous enough to use this finish. If water remains on the surface, do not use.

TYPICAL PRODUCT PROPERTIES: (51092)

COVERAGE/THINNING:
Covers approximately 75-150 sq. ft. (7-14 m2)
per gallon, depending upon surface porosity.
Do not thin.
FILM THICKNESS: N.A. does not form a surface film.
DRY TIMES: Apply only when surface and air temperatures
are 50-90°F (10-32°C). Dries in 1 hour.

VEHICLE TYPE: SOLIDS:
VOC:
WT/GAL: VISCOSITY:
FLASHPOINT:
60º GLOSS:

Silicone Emulsion
6% WT. 6% VOL.
100 g/L max
8.3 lbs.
8-12 Sec #4 Ford Cup
N.A.
Flat

APPLICATION:
Use a roller or low-pressure garden type sprayer. While the
first coat is still wet, apply a second coat to maximize
protection. Allow 5-10 minutes for final penetration, then use
a clean, dry cloth to wipe off all excess which did not soak
into the surface. Do not pond or puddle this product.

CLEAN UP:
Clean up with warm, soapy water.

PACKAGING:
Gallons 4 Pack

STORAGE AND DISPOSAL:
Do not freeze. Keep container closed when not in use. Do
not transfer contents to other containers for storage or
disposal. In case of spillage, absorb with inert material such
as sand or kitty litter. Dispose of contaminated absorbent,
container and/or unused contents in accordance with local,
state and federal regulations.

Product Information Hotline:
1-800-458-0047

CAUTIONS:
May cause eye and skin irritation. Avoid breathing vapors or
spray mist. If painting indoors, open windows and doors or
use other means to ensure fresh air entry during application and
drying. If you experience eye watering, headache or dizziness,
or if air monitoring demonstrates vapor/mist levels above
applicable limits, wear an appropriate, properly fitted respirator
(NIOSH approved) during and after application. Follow
respirator manufacturer’s directions for respirator use. AVOID
CONTACT WITH THE EYES AND SKIN. Wash thoroughly
after use. Close container after each use.

FIRST AID:
EYE CONTACT: Flush thoroughly with water for at least 15
minutes. If irritation persists, get medical attention.
IF INHALED: If affected by vapor or spray mist, move to fresh
air. If breathing difficulty continues, get medical attention.
IF SWALLOWED: Drink 2 glasses of water.
Get medical attention immediately.

DO NOT TAKE INTERNALLY.
KEEP OUT OF REACH OF CHILDREN.
For additional safety and chronic health
hazard information, refer to the Material
Safety Data Sheet for this product.
EMERGENCY MEDICAL TELEPHONE:
1-888-345-5732
This product contains less than
100 g/L VOC (0.8 lb./Gal VOS)

TYPICAL ANALYSIS (51092)

CAS No.
7732-18-5
Not Avail.
Not Avail.

34375-28-5 2

Ingredients
Water
Silicone Emulsion
Polydimethylsiloxane
With Emulsifier
Hydoxymethylamino Ethanol

WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how
to protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.

Sept-07

The data on this sheet represent typical values. Since application variables
are a major factor in product performance, this information should serve
only as a general guide. We assume no obligation or liability for use of this
information. UNLESS WE AGREE OTHERWISE IN WRITING, WE
MAKE NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIM ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. WE WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the replacement of the defective product, or a refund of its purchase price, at our option.

Download

PDF Format

[ Additional Product Information 1 - 2 - 3 - 4 - 5 - 6 - 7 ]

[Home] [Designs] [Technical Drawings] [Product Information] [Company Information] [Portfolio]

[ CONTACT - Classic Garden Ornaments, Ltd. ]

[ SEARCH ]

Classic Garden Ornaments, Ltd., designs and manufactures high quality, dry cast limestone Longshadow planters, pedestals, finials, figures, pool surrounds, benches, birdbaths and beautiful barriers in Arts & Crafts, Prairie and Traditional styles, for exterior residential and commercial use.

Dry cast limestone has the texture, appearance and durability of carved limestone at a fraction of the cost. Dating to Roman times, dry cast limestone has a natural porosity that makes it frost-proof and enables it to withstand decades of weathering. Dry-cast limestone is suitable for all-season exterior use for residential and commercial, street and mall site furnishings.